Menushopping cart
Tools for Working Wood
Invest in your craft. Invest in yourself.

JOEL Joel's Blog

Robert Towell Infill Planemaker - London c. 1810-1850


Robert Towell Infill Planemaker - London  c. 1810-1850 4My friend Raney Nelson dropped by the showroom yesterday and asked me to bring in some interesting infill plane. Lately he told me he has been thinking about making a mitre plane and I thought bringing in one might be interesting enough. "Mitre" is the English spelling of "miter", but I always use the English spelling because the mitre plane is a distinctly English phenomena. I own older mitre planes but Towell is considered the first of the full-time English infill makers and he built the first signed infill panel plane that we know of today and probably the first infill rebates planes too.

In general his work always shows elegance and in some cases innovation as infill design struggled to mature, something it finally did in the hands of Steward Spiers the most prominent of the next generation of infill planemakers.

This particular plane has a 2" iron and is fairly typical of mitre planes from before the mid 19th century. The sole is steel and the sides are wrought iron.

The secret to a well performing mitre plane is a very tight mouth both in frontRobert Towell Infill Planemaker - London  c. 1810-1850 5 of the iron and in back, supporting the iron to the very edge. This is because with a bevel up iron, even if the iron is supported close to the cutting edge, the bending moment of the iron around the body is at a very thin section, at some point at the bevel. In a bevel down plane the bending point of the iron is further along the iron well away from the bevel. (That's why it's easier to make a good bevel down plane than bevel up plane.) In any case comparing pretty good mitre planes to really excellent ones instantly shows the important of a fine mouth behind the iron.

Robert Towell Infill Planemaker - London  c. 1810-1850 6Towell's mitre planes are constructed just like his contemporaries, with the sole tongue and grooved together around the mouth, and the sides dovetailed in. However one thing I really like about Towell's planes is his most elegant and curvaceous bridge.
Incidentally before you ask, the chances that Towell had any metal working tools other than a few hacksaws, a few metal cutting chisels, a forge, and a lot of files is pretty small. This plane was done all by hand.

I'm guessing that this plane is fairly early in his career, and of all the types of planes Towell made, the mitre plane is the most common. It's also the earliest form of infill that existed and the jumping off point for Towell and other innovators.
Join the conversation
10/08/2009 Stephen Shepherd

Nice plane, I hope some one starts making them like the originals with thin iron sides.

My question is when did they start calling them 'infill' planes, early references are to 'clad' planes?

"Clad" can also refer to a wooden plane with iron screwed to Sole and (sometimes) sides. Still the question is worth asking. I don't know the answer offhand and need to do some research.
10/09/2009 Scott MacLEOD
I'm missing/unable to read some of the text between "However" and "elegant and curvaceous bridge".

Thanks, Scott
12/06/2009 Bob Wooten
Did they ever make mitre planes bevel down? Looks like if you pitched the blade at 35 degrees and sharpened it at 30 degrees you would have a good arrangement for end grain trimming. It would be much easier to make the wide mouth opening that this arrangement would require while still keeping the close clearance needed ahead of the blade edge.

Or did they ever try using the sharpening approach Leonard Lee describes for lowering the cutting angle in a standard block plane? 20 degree pitch bevel up, 15 degree top bevel, 10 degree back bevel to get a 35 degree cutting angle with a 25 degree edge. You could have a wider mouth opening and adjust cutting clearance at the mouth by the width of the back bevel relative to the top bevel. That would be more trouble to sharpen just right but it should work. An adjustable mouth would make it easier.
To answer your questions:

Wooden mitre planes were made with about a 35 degree bed angle. They are mostly American and kind of rare. They work OK. It is my opinion that using a low angle plane for end grain is largely a myth and most purpose made shooting planes of the 19th century were bevel down bench planes. Stanleys cute board plane is one example. I will be writing more on historical uses of the mitre plane soon.

If someone did sharpen a plane as Leonard Lee describes is certainly wasn't a common practice for the above reason.

The only historical reason for an adjustable mouth is the ease of manufacture. I don't think I have EVER taken apart an old Stanley and found any evidence that the frog was EVER adjusted. Wooden planes and Infill planes were not made with adjustable mouths and in the former mouths on worn planes were repaired.
01/13/2011 Makita Tools
I wasn't aware of the English origin of mitre. This one looks beautiful. Is it true that most of the new mitrers are made by wood? Is wood better than steel and iron?. Thank you.
Comments are closed.
The opinions expressed in this blog are those of the blog's author and guests and in no way reflect the views of Tools for Working Wood.