Menushopping cart
Tools for Working Wood
Invest in your craft. Invest in yourself.

JOEL Joel's Blog

Further Thoughts On Grinding


Further Thoughts On Grinding 4Four years ago (June 08) I wrote an article for Fine Woodworking Magazine on how to use a high speed dry grinder. It was a popular article and I still see it referenced today. The method that the article suggested involved slightly cambering the grinding wheel, a technique I learned from Barry Iles.

Four years later I think some clarification on how I use the cambered wheel might be in order.
Further Thoughts On Grinding 5The point of the camber isn't to make an effectively narrower wheel. It's to allow control when grinding.

Fig 1 is a side view of what happens when you start grinding. - the iron touches the wheel at one point on the bevel. As you grind you end up with Fig 2 - where the wheel has formed a hollow grind. As you can see, the cutting edge of the blade never touches the grinding wheel until you are done.
Further Thoughts On Grinding 6

At the center of an iron when starting to grind with a cambered grinding wheel you get fig 3 - again a point contact, but as you grind (let's just assume for a second you are not going back and forth on the rest) you get fig 4. It's important to realize that the cutting edge is still straight across because we haven't touched it yet. The first photo shows the Further Thoughts On Grinding 7 grind marks on an iron where I just touched the blade to a cambered wheel (the cutting edge is downward). The grind marks form a football shape because of the convexity of the wheel. The next photo shows the same iron after I start moving it back and forth on the rest and in the close-up you can see that the grinding isn't perfectly even and the section in the middle is ground a little deeper and I am close to the cutting edge but not there.

So far so good. The camber on the wheel makes it possible for me to easily control where I am grinding and keeps me from overly grinding the corners of my iron where it is easy to burn stuff.

Further Thoughts On Grinding 8You can see that as long as the camber of the wheel is very shallow (like it is) I am grinding almost the full width of the wheel once I get going. When I start I have a small point of contact and lots of control, as I get more and more hollow ground, I am also in contact with, and grinding, using more and more of the wheel's width.

But wait - there's more!!

In order to get an even hollow I need to move my iron back and forth, with the camber I can easily control how much pressure I use. I do this by tilting the blade into the wheel as I grind.

Of course as I am doing this I am paying attention to the heat in my fingers from the grinding and visually checking how far I am gone and what parts of the iron still need work.

You can see on the left in the last photo of the finished iron that the scratch marks aren't perfectly parallel to the marks in the center of the grind. This shows the result of tilting the iron into the wheel (fig. 5). With tilting I have a reliable way to grind quickly or ease off on the sides of the iron. This is very important at the end of the process when I am frequently picking the iron up, seeing where I need to grind more and replacing the iron on the rest. I push forward, making contact with the wheel and then tilt the iron into the wheel as I move back and forth, This gives me a lot more control than if I tried to just move the iron by eye perfectly straight left to right.

Further Thoughts On Grinding 9Getting rid of most of the hollow took about 20 seconds (plus two stops for photographs). I had noticed when I started grinding the wheel was a bit dull and it could have used a dressing but I waited until I was near the end of the process so that I had a fresh clean cool wheel for the last, most "risky" bit. So without moving the rest or anything I did a very light dressing just before the final steps. Then I ground what's left of the hollow and every few seconds picked up the iron to look at to I could make sure I am grinding evenly. It took about 30 seconds more. There is a small, easily felt, evenly sized burr on the back of the iron which tells me that I have ground to the edge. It is even across the iron so I must have ground evenly.

During the entire grinding process the iron never got more than warm. I used a 6" 3600rpm grinder with 60 grit 3X wheels.

Try it yourself - it's easy.

Note: To make the camber on the wheel I just used a multi-point diamond dresser. Fine Woodworking has the original article available somewhere in their on-line archive.

Join the conversation
10/09/2012 joe
Joel, When moving the blade left to right do you use a grinding jig? or just the factory tool rest. Awhile ago I saw someone replacing the left and right tool rests with a round steel bar reaching across both wheels and then clamping a stop onto the blade. I've always used my hand/finger as a guide on the tool rest. But then again I'm always fighting to get a straight...square edge.
I use the factory rest. If I used any other jig I would not be able to easily pick up, check, and replace the iron, tilt it into the curvature, and vary the pressure.
Grinding to a wire edge or a line is just like planing to the line. You pay attention to what you are doing, as you approach the line you plane selectively if you need to, and with a bit of practice you get a sense over how heavy a cut you can make, and where to apply pressure.
10/09/2012 Rob Porcaro

This makes such good sense, much like the control with a cambered plane blade.

Any suggestions on using your method with the wide grinding wheel on a Tormek?


I don't have a tormek so I don't know, but isn't the whole point of the machine the jigs and setups?
10/10/2012 Bruce Wedlock
You didn't give any info on how much camber you use on the wheel. Roughly how much are the edges of a one inch wide wheel in from its center?
The smaller the amount of camber the better - as then it's easier to use more of the width of the wheel. You just need a tiny bit of relief. I try for about 1/64" but more isn't a problem - so don't sweat it if you end up with say a 1/16". It isn't critical one way or another as long as the camber isn't zero.
Comments are closed.
The opinions expressed in this blog are those of the blog's author and guests and in no way reflect the views of Tools for Working Wood.